A crack in the bathroom ceiling, a bulge in the plaster, then one day a chunk of concrete on the floor with rusty steel showing above it. That is spalling concrete, and it is common in older HDB flats, especially in bathrooms and kitchens where the air is warm and damp.
Spalling is not only an eyesore. Falling concrete can injure someone, and the rusting steel inside the slab keeps weakening it until the problem is properly repaired. This guide explains what causes spalling, how to tell it apart from a ceiling leak or flaking paint, who is responsible and who pays, the repair steps that actually stop it coming back, and what it typically costs.
What spalling concrete is
HDB slabs are reinforced with steel bars set inside the concrete. The concrete normally protects that steel, because fresh concrete is strongly alkaline and keeps the steel from rusting.
Over decades, carbon dioxide from the air slowly reacts with the concrete and lowers its alkalinity. This is called carbonation, and HDB identifies it as the main cause of spalling in flats. Once carbonation reaches the steel and moisture is present, the steel starts to rust. Rust takes up several times the volume of the original steel, so it pushes outward, cracks the concrete cover and eventually breaks pieces off.
Two conditions speed this up:
- Moisture. Bathrooms, kitchens and ceilings below leaking floors keep the concrete damp, which feeds the rusting.
- Thin concrete cover. Where the steel sits close to the surface, carbonation reaches it sooner.
This is why spalling clusters in older flats and in wet rooms.
Spalling, ceiling leak or flaking paint?
These three look similar at first and are often confused. The fix for each is different.
| Sign | Spalling concrete | Ceiling leak | Flaking paint |
| Surface | Cracks, bulges, concrete falling off | Water stain, damp patch, dripping | Paint peeling, concrete underneath intact |
| Rust | Rust stains or exposed steel bars | Usually none unless long-running | None |
| Wetness | May be dry | Damp or wet, often linked to water use above | Usually dry |
| Sound when tapped | Hollow over the affected area | Normal or soft if saturated | Normal |
| Main risk | Falling concrete, slab weakening | Water damage, mould, electrical risk | Cosmetic |
The two can also happen together. A long-running ceiling leak keeps the slab wet, and that speeds up spalling. If your ceiling is both stained and spalling, the leak has to be fixed first, or the new repair will fail. Our ceiling leakage repair page covers how inter-floor leaks are traced.
Safety first: what to do when concrete falls
Spalling concrete can drop without warning. If you see cracked, bulging or loose concrete:
- Keep people away from the area below, especially children and elderly family members.
- Do not shower or stand under a spalling bathroom ceiling until it is made safe.
- Remove loose pieces carefully only if they are small and you can reach them safely. HDB’s guidance for removing loose concrete is to wear a safety helmet, gloves and eyewear, lay cardboard over the floor to protect it, and dispose of the debris through the bin chute.
- Do not hack at sound concrete to “check” it. That creates more damage.
- Arrange a repair promptly. Exposed steel keeps rusting once the cover is gone.
If spalling is in a common corridor, staircase or on the external facade, report it to your Town Council, as these are common property.
Who is responsible?
HDB is clear on this. As the flat owner, you are responsible for preventing spalling concrete in your flat and for any repair work it needs. The responsibility depends on where the spalling is:
| Location | Responsible party |
| Inside your flat (ceiling, walls, beams) | Flat owner |
| Common corridors, staircases, void decks | Town Council |
| External facade and common property | Town Council |
Source: HDB home care guide on spalling concrete (updated July 2026).
Who pays? GRA, HIP or private repair
Even though owners are responsible, there are two government programmes that can reduce or cover the cost.
Goodwill Repair Assistance (GRA)
In an October 2022 written answer to Parliament, MND explained that under the GRA scheme HDB helps flat owners arrange spalling repairs and co-pays 50% of the cost for Singapore Citizen households. The owner pays the other 50%, capped at S$300 per flat. For rental flats, HDB bears the full cost.
Worked example
| Item | Amount (SGD) |
| Repair cost for spalling ceiling | $900 |
| HDB co-payment (50%) | $450 |
| Owner’s 50% share | $450, capped at $300 |
| Owner pays | $300 |
| HDB pays | $600 |
The cap is on the owner’s share, so on larger repairs it can save a meaningful amount. HDB’s current web page describes owner responsibility and DIY repair but does not spell out GRA, so confirm eligibility and the current terms with your HDB Branch.
Home Improvement Programme (HIP)
For older blocks selected for HIP, repair of spalling concrete and structural cracks is part of the Essential Improvements, which are fully funded by the government for eligible Singapore Citizen households. HIP covers blocks built up to 1997. If your block is due for HIP soon, it may make sense to wait for that programme for large-scale spalling, while making any immediate safety risk safe in the meantime.
Private repair
If you are not eligible for GRA, your block is not under HIP, or you want the work done sooner or to a different specification, you can engage a contractor directly.
Decision table
| Your situation | Best route |
| Singapore Citizen household, spalling inside the flat, no HIP soon | Apply for GRA through HDB Branch |
| Block selected for HIP, not an urgent safety risk | Wait for HIP, make immediate hazards safe |
| Not eligible for GRA, or need a faster or wider repair | Private contractor |
| Spalling in corridor, staircase or facade | Report to Town Council |
| Small area, owner comfortable doing DIY | DIY following HDB’s steps |
How spalling is repaired properly
HDB allows owners to repair small areas themselves and sets out the method. Larger areas should be handled by a contractor. Either way, the sequence is the same:
- Remove loose and hollow concrete until you reach sound concrete all around the affected area.
- Expose the rusted steel fully, so the whole corroded length can be treated.
- Clean the steel by wire brushing until the rust is removed.
- Apply two coats of anti-rust (rust-inhibiting) paint to the steel bars.
- Apply a bonding agent to the concrete surface so the new material grips the old.
- Patch with polymer-modified cement mortar, built up in layers to restore the concrete cover over the steel.
- Finish and paint once the mortar has cured.
For a bathroom ceiling, many contractors also apply an anti-carbonation or moisture-resistant coating over the finished patch, which slows future carbonation.
Why patches fail
A repair can look perfect and still fail within a year or two. The usual reasons:
- The moisture source was not fixed. If the bathroom upstairs leaks, the slab stays wet and the steel keeps rusting behind the new patch.
- Not enough concrete was removed. Leaving rusted steel buried at the edges means the corrosion continues just outside the patch.
- The steel was painted over rust. Anti-rust paint over loose rust does not stop corrosion.
- Ordinary cement or plaster was used instead of a polymer-modified repair mortar, so the patch cracks and debonds.
If your ceiling spalls and also shows damp patches, have the leak above checked as part of the job. Bathroom floor leaks are a common cause, and we cover them in our bathroom and toilet leakage repair service.
What it costs
Advertised market prices for spalling repair in Singapore vary with the size of the area, access and whether waterproofing is needed. Typical ranges:
| Scope | Advertised range (SGD) |
| Single small patch | $200 to $600 |
| Larger patch or multiple spots in one room | $600 to $1,200 |
| Whole bathroom ceiling, including coating | $800 to $2,000+ |
| Spalling repair plus fixing a leak above | Higher, depends on the leak repair |
Remember that under GRA, an eligible owner’s share is capped at S$300, so check eligibility before paying a private quote in full.
How HDB monitors older flats
MND has described several inspection regimes that relate to spalling and structural safety:
- Residential buildings undergo a periodic structural inspection every 10 years.
- Since 2022, HDB inspects flats completed before 1 January 1989 every 5 years to spot issues such as spalling early.
- Buildings more than 20 years old and taller than 13 metres undergo periodic facade inspections every 7 years.
These inspections help catch problems, but they do not replace keeping an eye on your own ceilings, especially in bathrooms and kitchens.
How to slow spalling down
- Fix ceiling leaks and bathroom floor leaks quickly, so the slab does not stay wet.
- Ventilate bathrooms after showers with an exhaust fan or open window.
- Repaint ceilings with a moisture-resistant or anti-carbonation paint when redecorating.
- Check ceilings every few months for hairline cracks, rust stains or bulges, and repair early while the patch is small.
Frequently asked questions
Is spalling concrete dangerous? It can be. Falling pieces can injure people, and the rusting steel keeps weakening the slab. Small spalls are not usually a structural emergency, but they should be repaired promptly.
Can I repair spalling concrete myself? HDB allows DIY for small areas and sets out the method. For larger areas, bathroom ceilings above head height, or spalling linked to a leak, use a contractor.
Does HDB pay for spalling concrete repair? Under GRA, HDB co-pays 50% for eligible Singapore Citizen households, with the owner’s share capped at S$300 per flat, according to MND in 2022. HIP Essential Improvements cover spalling for eligible blocks. Confirm current terms with your HDB Branch.
Why does my spalling keep coming back? Usually because the moisture source was not fixed, or not all the rusted steel was exposed and treated. A lasting repair deals with both.
Get spalling assessed and repaired
Flux Solutions repairs spalling concrete and the leaks that often cause it, using the remove, treat and rebuild method that keeps patches from failing. We are a BCA-registered and bizSAFE 3 certified contractor established in 2010. See our general works and concrete repair service or contact us.
Flux Solutions Pte Ltd 55 Serangoon North Ave 4, #02-11 S9, Singapore 555859 Phone: +65 6226 6116 Email: sales@flux.com.sg Website: https://glutenfreepleasure.com/__proxy_domain/flux.com.sg
Sources: HDB home care guide on spalling concrete (updated 27 Jul 2026); MND written answer on inspection of HDB flats over 40 years old and assistance to owners (20 Oct 2022). Scheme terms can change, so confirm with your HDB Branch.
